Cleaning chemicals include alkaline, acidic, neutral, solvent-based and disinfectant products used to remove different types of soil from commercial surfaces. Using them safely requires an understanding of pH, dilution and the information provided on the product label.
Property managers may not select every cleaning chemical themselves, but they still deal with the results of incorrect product selection. These can include a dull lobby floor, stained aluminium frames or washrooms with strong chemical odours.
This guide from MGC Maintenance Services explains the main types of cleaning chemicals, how pH affects different surfaces and why correct dilution is an important safety control. It also covers chemical combinations that must never be mixed and what cleaning teams should look for on GHS labels and safety data sheets in Malaysia.
The Five Main Types of Cleaning Chemicals Used in Commercial Properties
Commercial cleaning programmes typically use several types of chemicals, each designed to tackle particular soils and surfaces. Understanding the purpose of each type helps cleaning teams select the appropriate product and avoid unnecessary surface damage.
Alkaline Detergents and Degreasers
Alkaline cleaning products have a pH above 7 and are effective at breaking down fats, oils and protein-based soils. They are commonly used in areas such as kitchens, loading bays and car parks where grease and oil may accumulate.
The stronger the alkalinity, the greater the potential risk to skin, eyes and sensitive surfaces. The product should therefore always be used according to the manufacturer’s instructions.
Acidic Descalers
Acidic cleaning products have a pH below 7 and are designed to dissolve mineral deposits such as limescale, rust stains, soap scum and some cement residues.
They are commonly used in washroom cleaning and post-construction cleaning. However, acids can etch natural stone and corrode certain metals, making correct surface identification essential before use.
Neutral Floor and Surface Cleaners
Neutral cleaners have a pH close to 7 and are suitable for routine cleaning of many sealed floors, stone surfaces, laminates and glass.
They can remove light everyday soil without aggressively stripping finishes or sealers. However, they are generally less effective against heavy grease, oil and mineral scale.
Solvent-Based Cleaners
Solvent-based cleaning products can dissolve substances such as adhesive residue, marker ink, tar and some paint overspray that water-based cleaners may struggle to remove.
Some solvents are flammable or produce vapours, so appropriate ventilation, storage and handling procedures are essential.
Disinfectants
Disinfectants are designed to reduce microorganisms on surfaces that have already been cleaned. They should therefore be used as part of a cleaning process rather than as a replacement for cleaning.
For a disinfectant to work effectively, the product must be used at the correct dilution and allowed to remain on the surface for the contact time stated on the label.
Why Does pH Matter When Choosing a Cleaning Chemical?
The pH scale runs from 0 to 14, with 7 considered neutral. Each whole number represents a tenfold change in acidity or alkalinity. This means a product with a pH of 12 is significantly more alkaline than one with a pH of 11.
Different surfaces in Malaysian commercial buildings respond differently to acidic and alkaline products. Before choosing a chemical, the cleaning team should identify both the surface material and its finish.
Polished Marble, Limestone and Terrazzo
Marble, limestone and travertine are calcium carbonate-based stones that can react with acidic products. Acid exposure can cause etching, leaving a dull or damaged area where the polished surface has been affected.
Etching is a physical change to the surface, so additional cleaning chemicals will not normally reverse it. Restoration may instead require processes such as mechanical honing or polishing.
Terrazzo containing marble chips can also be sensitive to acidic cleaning products.
Aluminium and Anodised Finishes
Aluminium cladding, window frames and signage may have anodised or coated finishes that can be damaged by strongly acidic or alkaline products.
Incorrect chemical selection can leave stains, streaks or dull areas that cannot simply be wiped away. Neutral or near-neutral cleaners are generally a safer choice for routine cleaning, but supplier guidance should always be followed and unfamiliar products should be tested on a small, inconspicuous area first.
Stainless Steel and Sealed Floors
Chlorine bleach can cause staining and pitting on stainless steel if it is left on the surface, which can be particularly problematic for lift interiors, handrails and other high-contact areas.
Sealed floors have different vulnerabilities. Strongly acidic or alkaline products may damage or strip the finish, resulting in uneven or patchy areas.
For routine cleaning, a suitable neutral cleaner at the manufacturer’s recommended dilution is often the safer option.
How to Match a Cleaning Chemical to the Soil and Surface
Before approving a cleaning product for use on a commercial site, several basic checks can help prevent chemical damage.
Consider:
- The surface material and its finish, including any sealers or coatings
- The type of soil being removed, such as grease, mineral scale, adhesive or general dust
- The supplier’s recommended dilution and contact time
- Ventilation, personal protective equipment and storage requirements stated on the label
- A small test area when the product has not previously been used on the surface
These checks should form part of the site’s cleaning procedures, particularly when introducing a new chemical or cleaning an unfamiliar material.
Why Is Dilution Important for Cleaning Chemicals?
Most commercial cleaning chemicals are supplied as concentrates that must be diluted with water before use. The product label should specify the appropriate dilution ratio for each application.
Although dilution can help control cleaning costs, it is also an important safety measure. Concentrated chemicals can be more corrosive or irritating to the skin, eyes and respiratory system than the diluted solution intended for application.
This is particularly relevant during periodic work such as commercial deep cleaning services, where stronger cleaning products may be required to tackle accumulated grease, scale and other difficult soils.
Using a chemical at a concentration stronger than recommended does not necessarily produce better results. Excess product can leave residue, increase worker exposure and damage surfaces. Conversely, using too little chemical may make the product ineffective and result in repeat cleaning.
Practical Ways to Control Cleaning Chemical Dilution
Metered dispensing systems, pre-measured sachets and clearly marked buckets can reduce guesswork and help maintain consistent dilution ratios between shifts.
Every container, including spray bottles and mop buckets, should be clearly labelled with its contents. Under the USECHH Regulations 2000, employers also have responsibilities concerning labels for chemicals hazardous to health and containers into which such chemicals are transferred.
A written product list can make chemical use easier to supervise and audit. For each area or surface, record the approved product, dilution ratio and required contact time.
Which Cleaning Chemicals Must Never Be Mixed?
Chemical incidents can occur when products that are safe when used separately are combined in the same bucket or spray bottle.
The safest general rule is simple: never mix cleaning products unless the manufacturer’s instructions specifically state that they can be mixed.
Bleach and Acids
Chlorine bleach must not be mixed with acidic products such as descalers or some toilet cleaners. The combination can release chlorine gas, which can irritate the eyes, nose and throat and cause serious breathing difficulties at higher concentrations.
Washrooms are a particular area of concern because different cleaning products may be used on the same surfaces.
Bleach and Ammonia
Bleach must also not be mixed with ammonia-containing products, which may be found in some glass and multi-surface cleaners.
The combination can produce harmful chloramine vapours. Residual chemicals can also react with another product applied later, so surfaces should be rinsed appropriately when changing between incompatible products.
How to Read a GHS Label and Safety Data Sheet in Malaysia
Malaysia adopted the Globally Harmonised System through the Occupational Safety and Health (Classification, Labelling and Safety Data Sheet of Hazardous Chemicals) Regulations 2013, commonly known as the CLASS Regulations.
The regulations were gazetted on 11 October 2013 and establish requirements relating to the classification, labelling and safety data sheets of hazardous chemicals. They also include exclusions, meaning not every product will necessarily carry a CLASS label.
Employers using chemicals hazardous to health have separate responsibilities under the USECHH Regulations 2000, including conducting a written chemical health risk assessment where required.
What Information Does a GHS Label Provide?
A GHS label provides important information about the hazards associated with a chemical. Depending on the product, this can include:
- Product identifier
- Supplier details
- Signal word, such as Danger or Warning
- Hazard pictograms
- Hazard statements
- Precautionary statements
The signal word and pictograms provide a quick indication of the hazards, while precautionary statements provide information about safe handling, storage, personal protective equipment and first aid.
What Does a Safety Data Sheet Tell You?
A safety data sheet provides more detailed information and follows a standard 16-section format.
Four sections are particularly useful when reviewing cleaning chemicals for a commercial site.
Section 2: Hazard Identification
This section describes the chemical’s hazard classification, pictograms and signal word. It also summarises relevant health, physical and environmental hazards.
It is an important section to review before approving a new product for use on site.
Section 7: Handling and Storage
This section explains how the product should be handled and stored. It can include information about ventilation, storage conditions and materials that should be kept apart.
Cleaning chemical storage areas should be organised in accordance with these requirements, such as keeping incompatible chemicals separated.
Section 8: Exposure Controls and Personal Protection
This section provides information about exposure controls and recommended personal protective equipment, which may include gloves, eye protection and respiratory protection.
The recommendations should correspond with the equipment actually provided to workers on site.
Section 10: Stability and Reactivity
This section identifies conditions and materials that may cause a chemical to react. It can therefore help determine which products must be kept separate and which combinations should be avoided.
Section 9 also provides information about physical and chemical properties, including pH, linking the safety data sheet back to the surface and product checks discussed earlier.
Where a chemical is hazardous to health, the USECHH Regulations 2000 also include requirements relating to access to the relevant safety data sheet in the workplace.
How to Put Cleaning Chemical Control Into Practice
Effective chemical control comes down to four consistent practices:
- Choose the product according to the soil and surface.
- Dilute the product exactly as directed by the manufacturer.
- Keep incompatible chemicals separated.
- Keep product labels and safety data sheets accessible to the people using the chemicals.
These practices do not necessarily require specialist equipment, but they do require appropriate training, supervision and consistent site procedures.
Property managers and facility teams reviewing the chemicals used on their sites can contact MGC Maintenance Services to discuss their premises and cleaning requirements.
A written chemical register or product list showing the approved product, surface, dilution ratio and contact time can be a practical starting point for improving chemical control across a commercial property.
Frequently Asked Questions
Cleaning chemicals are products formulated to remove specific types of soil from surfaces. Common categories include alkaline detergents, acidic descalers, neutral cleaners, solvents and disinfectants. The appropriate product depends on both the soil being removed and the surface being cleaned.
The terms are often used interchangeably in facility management. A cleaning agent is a broader term for a substance that helps remove soil, while cleaning chemicals commonly refers to the formulated products used by cleaning teams.
pH helps indicate whether a product is acidic, neutral or alkaline and can affect both its cleaning performance and its compatibility with different surfaces. Acidic products, for example, can damage acid-sensitive stone, while strongly alkaline products may affect some finishes and metals.
No. Using a cleaning chemical at a stronger concentration than recommended can increase residue, worker exposure and the risk of surface damage. The manufacturer’s recommended dilution should be followed for the intended application.
Chlorine bleach should never be mixed with acidic products or ammonia-containing products because harmful gases or vapours can be produced. More generally, cleaning chemicals should not be mixed unless the manufacturer specifically states that they are compatible.
Suppliers of chemicals classified as hazardous have responsibilities under the CLASS Regulations 2013 regarding safety data sheets. The regulations include certain exclusions, so the requirements can vary depending on the product. The relevant safety data sheet should be obtained and made accessible before a hazardous chemical is used where required.